sew and flip titleHi – I’m Angel with FleeceFun.com, a website that features free sewing patterns and tutorials.  For this tutorial I’m showing you how to make a sew and flip receiving quilt.  This step by step tutorial is perfect for beginners.  Be sure to watch the video to fully understand the process!  You can find a full video tutorial on Shannon’s YouTube channel here.  While you’re there, be sure to subscribe so you don’t miss any of their free tutorials!

You Will Need:

1 Cuddle Strip Kit

1 Yard of Cuddle Fabric (for Backing)

1 yard and 1/8 Low Loft Batting

Marker

Temporary Spray Adhesive

Walking Foot

#90/14 Stretch needle

Rotary Cutter, Ruler and Mat

1 – Cut out the pieces

receiving quilt0001receiving quilt0002receiving quilt0003receiving quilt0007receiving quilt0008receiving quilt0009 Cut off the selvage of the strips and the backing.

Cut fabric backing to 36” by 36” inches.  Be sure to save the excess fabric for binding and other projects.

Out of the excess backing fabric cut 4  2 inch wide stripes that are 36 inches in length.

Cut 9 Cuddle strip to 36 inches in length ( be sure to trim off the selvage).

Cut the Batting so it’s a few inches bigger than 36” by 36” ( about 40” by 40”).

Tip: you can skip the batting to make a lighter blanket – but for a beginner it’s easier to sew with the batting as the Cuddle can shift due to the stretch.

2 – Adhere backing to the batting

receiving quilt0016receiving quilt0018receiving quilt0020receiving quilt0021receiving quilt0022Adhere the batting to the backing.  Using a large space on the floor, either pin or tape the edges of the batting down, lightly stretching it to make it taught.  Place paper underneath the edges to protect your floor from the temporary adhesive spray.  Center the fabric on the batting with wrong side facing down.  Spray fabric on the wrong side and slowly begin to adhere fabric to batting, working out wrinkles as you go.  If you mess up, quickly but gently lift the  fabric and try again.  Once fabric is attached to batting, remove from floor and trim off excess so batting is square with backing.

3 – Lay out blanket

receiving quilt0024receiving quilt0025receiving quilt0026receiving quilt0027receiving quilt0029receiving quilt0030receiving quilt0031Lay out strips in desired order, be sure to check the nap as you go.  The nap will either lay smooth or go “rough”.  Keep petting your fabric to make sure it all lays the same direction.

Once you have your pattern figured out, take the center strip, and fold it in half length wise.   Mark fabric along the fold to establish the “center line”.

Take the backing and fold in half with the batting side out.  Mark on the batting along the fold the establish a center line.

Unfold the backing and lay out.  With the Cuddle strip still folded in half, line up the markings and use adhesive spray to lay into place.

4 – Sew and Flip!

receiving quilt0032receiving quilt0033receiving quilt0034receiving quilt0037receiving quilt0038receiving quilt0041receiving quilt0042receiving quilt0043receiving quilt0055receiving quilt0054Now it’s time to sew and flip! Making sure the nap is correct place the next Cuddle strip down (with right sides together on the center strip. ) Pin into place.  Sew through all the layers of fabric using a walking foot.  Use a straight stitch with a half inch seam allowance.  Once seam is complete spray wrong side of the strip that was sewn with adhesive and “flip” into place,  working out wrinkles as you go.  Keep alternating sides from the center strip.  Sewing the flipping until you reach the edge.  With the final outer strips be sure to spray into place.

 

5 – Trim

receiving quilt0056receiving quilt0045Since Cuddle has a stretch to it there will be excess on the sides.  Trim down the excess so it matches the backing.  We’re going to be cutting corners on this quilt (literally).  Take a plate and round off the corners of the blanket.

6 – Bind

receiving quilt0048receiving quilt0049receiving quilt0050receiving quilt0051receiving quilt0052For detailed instructions on binding please see the video here.  Sew the two inch strips together. Then sew on the backing with a straight stitch and a half inch seam allowance.  Fold over and sew down to the front using a serpentine stitch.  You’re finished! Be sure to subscribe to this blog for more tutorials like this one!shannon sew and flip

Written by Angel Hickman Peterson